300-615 Practice Dumps - Verified By BraindumpQuiz Updated 150 Questions [Q34-Q54]

300-615 Practice Dumps - Verified By BraindumpQuiz Updated 150 Questions

Updated 300-615 Exam Dumps - PDF Questions and Testing Engine

NEW QUESTION 34
The Cisco Nexus switch is connected to a peer switch that is not running Cisco NX-OS. The switches are connected using port channel and are experiencing packet loss. Which action should be performed on the Cisco Nexus switch ports to resolve this issue?

A. Turn off lacp graceful-convergence.
B. Turn off lacp suspend-individual.
C. Turn on lacp graceful-convergence.
D. Turn on lacp suspend-individual.

Answer: A

Explanation:
Section: Network

NEW QUESTION 35
An engineer enables the packet postcards feature on a Cisco Nexus 9000 Series Switch but receives the error message "Error: Cannot configure postcard when inband-telemetry is configured." Which action resolves the issue?

A. Disable the telemetry feature
B. Disable the hardware-telemetry feature
C. Disable the software-telemetry feature
D. Disable the inband-telemetry feature

Answer: B

Explanation:
Explanation
https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus9000/sw/93x/progammability/guide/b-cisco-nex

NEW QUESTION 36
A Fibre Channel interface on a Cisco Nexus 5000 Series Switch receives bit errors, and the switch disables the interface. A temporary workaround must be implemented before the root cause is identified. Which action does an engineer take to prevent this issue from reoccurring?

A. Run the shutdown and then no shutdown command on the interface.
B. Verify that the SFPs are supported.
C. Change the SFP to operate at 4 Gbps instead of 2 Gbps.
D. Run the switchport ignore bit-errors command on the interface.

Answer: D

Explanation:
Section: Storage Network
Explanation

NEW QUESTION 37
Refer to the exhibit.

The vPC neighborship between two switches is in suspended state. Which configuration change resolves the issue and brings up the vPC neighborship?

A. Enable Bridge Assurance on the local switches
B. Change STP Port Type to Network on the peer switch
C. Configure QoS MTU value of 9216 on the peer switch
D. Add VLAN 400-401 to the configuration on the local switch

Answer: C

NEW QUESTION 38
Refer to the exhibit.

After a failover occurs, which two actions must be performed on Switch-B to manually preempt the operational primary role back to Switch-A? (Choose two.)

A. Configure the local vPC role priority to have the same value as Switch-A.
B. Disable and then re-enable the vPC peer-keepalive link.
C. Configure the local vPC role priority to have a lower value than Switch-A.
D. Configure the local vPC role priority to have a higher value than Switch-A.
E. Disable and then re-enable the vPC peer link.

Answer: D,E

NEW QUESTION 39
Refer to the exhibit.

An engineer must strictly enforce the port security configuration database in the Fibre Channel fabric. A new device has been connected to the Fibre Channel storage interface that was configured for port security. The port security was enabled for the VSAN that the port belongs to. Despite the configuration, the rogue devices can log into the fabric. Which action resolves the issue?

A. Disable auto learn in VSAN 1 with the no port-security auto-learn vsan 1 command
B. Commit the changes with the port-security commit copy vsan 1 command
C. Commit the active database with the port-security database copy vsan 1 command
D. Disable CFS distribution with the no port-security distribute vsan 1 command

Answer: A

NEW QUESTION 40
An engineer is troubleshooting issues in Cisco UCS Director. Drag and drop the possible causes from the left onto the correct issues on the right.

Answer:

Explanation:

NEW QUESTION 41
Refer to the exhibit.

An engineer configures the server port on a Cisco Nexus 5000 Series Switch. The switch connects to an NPV edge switch port. The server fails to send the FC traffic to the fabric. Which action resolves the issue?

A. Enable the NPIV mode on the Cisco Nexus 5000 switch.
B. Replace the SFP in slot fc2/12.
C. Configure the BB_credit buffer on the uplink port.
D. Match the VSAN membership on both ends of the connection.

Answer: D

NEW QUESTION 42
A network administrator attempts to install an application in the Cisco NX-OS Guest shell and receives an error that there is not enough space on the disk. Which command must the administrator run to increase the disk space available in the Guest shell?

A. guestshell growdisk rootfs [size-in-MB]
B. guestshell resize rootfs [size-in-MB]
C. guestshell pvextend rootfs [size-in-MB]
D. guestshell resize2fs rootfs [size-in-MB]

Answer: B

NEW QUESTION 43
Drag and drop the commands from the left onto the correct categories on the right.

Answer:

Explanation:

NEW QUESTION 44
Refer to the exhibit.

An OSPF adjacency between Router-A and Router-B cannot reach the FULL state. Which action resolves the issue?

A. Adjust the MTU on Router-A to 1600.
B. Set the OSPF media type to point-to-point.
C. Disable the check of the MTU value.
D. Adjust the MTU on Router-B to 1604.

Answer: C

NEW QUESTION 45
Refer to the exhibit.

An administrator directly connects a Fibre Channel storage array to ports 1 through 4 on a Cisco UCS 6454 Fabric Interconnect. The administrator configures a service profile to boot directly from the new Fibre Channel storage array, but the service profile fails to boot. When the administrator checks the output of the show flogi database command on the fabric interconnect, it shows the output presented in the exhibit. Which action resolves the issue?

A. Configure the fabric interconnects in Fibre Channel end-host mode
B. Configure the Zoning Type in vHBA Initiator Group as Multiple Initiator Single Target.
C. Configure the fabric interconnects in Fibre Channel switch mode.
D. Configure the Zoning Type in vHBA Initiator Group as Multiple Initiator Multiple Target.

Answer: C

NEW QUESTION 46
Refer to the exhibit.

During implementation of a Cisco UCS C-Series Server, an engineer receives the status that is shown in the exhibit. Which action resolves the issue.

A. Insert an SD card into SLOT-2
B. Reconfigure the Drive Type from "Removable" to "Non-Removable"
C. Set SLOT-1 Sync Mode to "Auto"
D. Configure the RAID that is associated with the card.

Answer: A

NEW QUESTION 47
Refer to the exhibit.

A network administrator must delete a feature group from a Cisco Nexus 5000 Series Switch. Which action resolves the issue?

A. Detach the association with the no role command within the feature-group configuration mode
B. Detach the association with the no role command within the role configuration mode
C. Detach the association with the no rule command within the feature-group configuration
D. Detach the association with the no rule command within the role configuration mode

Answer: A

NEW QUESTION 48
The external routes fail to propagate to leaf switches in Cisco ACI fabric Which two actions resolve the issue?
(Choose two.)

A. Enable the VTEP pool in the fabric
B. Associate the correct contract to the L30ut.
C. Configure an MP-BGP area.
D. Specify the spine nodes as route reflectors
E. Assign an MP-BGP AS number to the fabric.

Answer: D,E

NEW QUESTION 49
You have an ACI environment with three APICs, two spine switches, and four-leaf switches. You wipe and reboot all APICs first then leaf and spine switches one-by-one and successfully go through the Initial Setuo dialogue on the APIC 1 CIMC KVM console. When you log in to the APIC1 WebGUI, you notice that you do not see any directly connected leaf switches being discovered under Fabric > Inventory > Fabric Membership. What is the cause of the issue?

A. The leaf nodes were not erased properly, which caused a fabric parameters mismatch with the APIC1.
B. Rebooting the APICs and the leaf and spine switches after wiping them is not required.
C. You forgot to enter the TEP Pool value during the Initial Setup dialogue on APIC1.
D. The same Fabric Name value should be used before after wiping all devices.

Answer: C

NEW QUESTION 50
Refer to the exhibit.

When an engineer inserts 8-Gb FC SFP port 15 on a Cisco UCS Fabric Interconnect, the port fails. What is a possible cause of the issue?

A. Port 15 is missing a license.
B. The polarity of the fiber cable is reversed.
C. Port 15 is configured for 4-Gb FC.
D. Port 15 is configured as an Ethernet port.

Answer: C

NEW QUESTION 51
A network engineer experiences the error "DDR3_P1_B1_ECC" when upgrading Cisco UCS firmware. Which action resolves the issue?

A. Reset the DIMM
B. Reset the BMC firmware
C. Reflash the controller firmware
D. Reflash the DIMM

Answer: A

NEW QUESTION 52
An engineer is troubleshooting a packet flow from an access leaf to spine. Which EVPN routes are expected on this connection?

A. EVPN Type 9-15
B. EVPN Type 0,9,15
C. EVPN Type 0,16
D. EVPN Type 1-5

Answer: D

NEW QUESTION 53
Refer to the exhibit.

An engineer is configuring boot from iSCSI on a Cisco UCS B-Series Blade Server, but the LUN fails to mount. Which action resolves the issue?